Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Tile & Stone Forums > Tile Forum/Advice Board

Sponsors


Reply
Thread Tools Search this Thread
Unread 04-14-2007, 06:34 PM   #1
ctewmey
Registered User
 
Join Date: Apr 2007
Posts: 1
How to tear down old wall tile in bathroom for remodel

I am looking for advice on how to tear down old wall tile in a standard size bathroom. I am having to replace the bathtub also. I thought I read somewhere that it was easier to cut the drywall and pull it all off and then replace the drywall.

Also, when I do tear down the wall and tile (if this is recommended by you) and remove the old tub. Does the drywall go up first and then the new bathtub installed?

I would greatly appreciate advice on this. I am planning to start this project in a couple of weeks.

Thanks, ctewmey
ctewmey is offline   Reply With Quote
Sponsored Links
Unread 04-14-2007, 06:59 PM   #2
Tool Guy - Kg
Moderator -- Wisconsin Kitchen & Bath Remodeler
 
Tool Guy - Kg's Avatar
 
Join Date: Feb 2005
Location: Oak Creek, WI
Posts: 21,326
Welcome, ctewmey.

Don't be afraid of giving us a first name to use. We're a friendly bunch.

Yes, removing the drywall with tile still on it is far easier than chipping off the tile. And because drywall is inappropriate for installing tile in a wet area, you're getting 2 birds with one stone by removing it all. You'll want a backerboard like Durock, or Permabase, or Hardibacker, or........

Use a flat bar to remove the outer bullnoses of the tile job (if any). Then run a drywall saw along the edge of the remaining tiles on all walls. Use that same drywall saw to cut a few "hand holes" right along the edge of the tiles so you can get a gloved hand in it. Then pull the drywall and tile off the wall. Start with the 2 side walls until they are out. Finish up on the back wall.

The tub goes up against the studs, so you need to take care of the tub installation before your backerboard and drywall patching is done.
__________________
Tonto Goldstein... but my friends call me Bubba

Help an awesome summer camp!
Tool Guy - Kg is offline   Reply With Quote
Unread 04-15-2007, 11:44 AM   #3
sabianq
Registered User
 
sabianq's Avatar
 
Join Date: Apr 2007
Posts: 29
i hope this helps,
I already tore one down, a 1957 bathroom, maybe this might give you some insight, I mover a wall 13 inches back to make a shower /bathroom, I in the middle of framing it. but the tear out took me a little over a 2 weekends, I am only doing this on my free time.

http://www.johnbridge.com/vbulletin/...007#post515007

and here is the shutterfly link my wife posted the pictures on.
http://projectbathroom.shutterfly.com/

the framing was not a load bearing wall, you need to assess whether the wall is load bearing, in general, if the wall runs perpendicular to the joists (cross ways) then there is a good chance that the joists are resting on the wall, but is the wall runs parallel to the joists, and it is located between joists, then it is not load bearing.
but you need to know! 100%
otherwise you need to support the joists when you are removing the wall.
you can still move load-bearing walls as long as you support the joists adequately

the tile was set in steel mesh with like 2 inches of concrete and then thinset then tile.

i used a pick to pull the tile off the wall in big chunks
oh and the waste it generates it big, i filled up a 15 yard roll off with an 80 sq ft bathroom and wall.

when i tore out the bathroom, i removed the entire thing, makes it easier to fix problems that you may not notice.

and drywall is cheap
__________________
"Silence is very expensive..."
Sab (me)
www.audioforums.com
sabianq is offline   Reply With Quote
Reply

Stonetooling.com   Tile-Assn.com   National Gypsum Permabase


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 09:05 AM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC