Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Tile & Stone Forums > Tile Forum/Advice Board

Sponsors


Reply
 
Thread Tools Search this Thread
Old 03-14-2018, 02:24 PM   #1
AJ Lane
Registered User
 
Join Date: Mar 2018
Posts: 1
Mitered Schluter rondec miss

I'm a DIYer with 0 previous experience. My wife and I just did our first tiling project, shower walls over a pre-made base and bathroom floors. There are imperfections, but overall we are pleased except for one corner of the Schluter Rondec trim we installed on the edge of the shower.

Home depot and the two tile shops we went to didn't carry the Rondec corner pieces on hand, so I figured I'd just go with mitered corners. The cuts lined up fine and looked fine in a dry fit, but we installed the walls first, then the ceiling and the rondec on one wall is 1/8" too low, so the corner doesn't meet up! (I must not have been holding the rondec all the way to the top of the edge like I should have when installing it! I blame the sharp edge up there catching on the very corner of the waterproofing membrane.)

So, what can I do to improve it at this point short of removing that first row of tiles along the edge? My first thought was to try gray metallic caulk (GE makes some). It's a slightly darker gray than the stain nickel of the aluminum edging I have, though. Any other ideas? Is there a shinier metallic caulk out there?
Attached Images
 
__________________
AJ
AJ Lane is offline   Reply With Quote
Sponsored Links
Old 03-14-2018, 05:18 PM   #2
Gozo
Registered User
 
Join Date: Oct 2016
Location: Central Virginia
Posts: 212
That looks like it’s not the mirrored finish metal, more matte or brushed. I had a similar (but smaller) gap when doing the same thing. I just grouted the space and it’s held up fine, no cracking. You could use a silicone that matches the grout. Colorsil makes it in most every color. I don’t think the silvery silicones will look acceptable; they remind me of last ditch effort to fix aluminum screen doors.
Here’s a pic of what I did:
http://www.johnbridge.com/vbulletin/...&postcount=119
That’s before grouting.
__________________
Jeff

Last edited by Gozo; 03-14-2018 at 05:19 PM. Reason: Detail
Gozo is online now   Reply With Quote
Old 03-14-2018, 08:27 PM   #3
makethatkerdistick
Registered User
 
Join Date: Oct 2017
Location: North Texas
Posts: 180
If you have a precise miter saw, you might be able to cut a mini piece of the Rondec and finagle it in there, holding it in place with caulk or grout.
__________________
Wolfgang
makethatkerdistick is offline   Reply With Quote
Old 03-14-2018, 10:52 PM   #4
Kman
Moderator
 
Kman's Avatar
 
Join Date: Nov 2006
Location: NW Arkansas, Ozark Mountains
Posts: 9,555
Caulk it, and if you can't find a matching caulk, find some paint to match and paint the caulk. As small as it is, it doesn't have to be that durable to hold up. Is it on the upper corner, as it appears to be in the picture? If so, it's not going to get that much moisture.
__________________
Kevin

The top ten reasons to procrastinate:

1.
Kman is offline   Reply With Quote
Reply

Stonetooling.com   Tile-Assn.com   National Gypsum Permabase


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Schluter Rondec PVC issues bc brick john Professionals' Hangout 2 06-10-2013 08:19 AM
Schluter Rondec duanec Tile Forum/Advice Board 1 10-23-2009 06:26 AM
Schluter Rondec Question RebelRidin Tile Forum/Advice Board 9 01-04-2009 10:47 AM
Schluter Rondec Auto tech Tile Forum/Advice Board 6 10-16-2002 09:27 PM
Schluter RONDEC BriGuy Tile Forum/Advice Board 2 10-11-2002 03:31 PM


All times are GMT -6. The time now is 10:11 PM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC