Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Tile & Stone Forums > Tile Forum/Advice Board

Sponsors


Reply
Thread Tools Search this Thread
Unread 01-17-2013, 09:27 PM   #1
scott-wisc
Registered User
 
Join Date: Nov 2009
Location: Stevens Point, WI
Posts: 20
New Windows

I have a few questions on replacing windows. The outside of the old windows have wood brickmould butted up to 8" aluminum siding. I ordered the new window (I'm starting out with just one for now), without trim and am going to use a 6" AZEK board to trim a frame around it. Obviously, I'll need to cut the siding to allow for the wider trim. So do I nail the window in place, tape over the nailers and piece in the trim boards and cualk all the joints? How tight should the trim be between the window and siding? The new windows are Andersen 100 Series.
Thanks, Scott.
__________________
scott w
scott-wisc is offline   Reply With Quote
Sponsored Links
Unread 01-17-2013, 11:15 PM   #2
cx
Moderator emeritus
 
cx's Avatar
 
Join Date: Jul 2001
Location: Boerne, Texas
Posts: 90,949
Welcome back, Scott.

You do understand we're a ceramic and stone tile site, yes?

I'd need a good deal more information about the construction of your house to properly answer your question, but the instructions that came with your window should give you a good idea how it is to be installed and properly flashed.

In general, aluminum siding is not caulked at all in my neck of the woods. It's generally trimmed against whatever other material it abuts.

My opinion; worth price charged.
__________________
CX

Y'ALL NEW VISITORS READ THIS HERE!
cx is offline   Reply With Quote
Unread 01-18-2013, 08:18 AM   #3
scott-wisc
Registered User
 
Join Date: Nov 2009
Location: Stevens Point, WI
Posts: 20
Yes, I know this is a tile site, but I'm too lazy to join a new forum. This window replacement is part of a chain of events that lead to my master bath remodel. I'm sure there's plenty of expertise here to help me out.
Everything gets caulked in Wisconsin.
Attached Images
 
__________________
scott w
scott-wisc is offline   Reply With Quote
Unread 01-18-2013, 09:39 AM   #4
John Bridge
Mudmeister
 
Join Date: Mar 2001
Location: Rosanky, Texas
Posts: 68,024
Send a message via AIM to John Bridge
Hi Scott,

I would slice through the caulking (siding/brick molding) joint, and remove the molding. The will expose the nails in the window flange. Maybe you can remove the window without destroying the paper-like flashing. That would be good.

I would then install the new window and cut my trim to fit against the siding. I would not cut the siding back simply to make room for new trim.
John Bridge is offline   Reply With Quote
Unread 01-18-2013, 03:12 PM   #5
ss3964spd
Moderator
 
ss3964spd's Avatar
 
Join Date: Jul 2005
Location: Fairfax, Va
Posts: 3,427
Send a message via Yahoo to ss3964spd
Scott,

You might find it less of a headache to simply remove the siding all together, install the new window and trim, then reinstall and clauk the siding.

I had a similar situation when I installed 3 new windows that didn't previously exist, and moved the door. Was far easier to remove the aluminum siding, do the framing and unit install, then put the siding back up than it would have been to cut the siding exactly to the correct width while in place.

Removing the siding will ensure you can attach the window correctly, as well as flash it correctly.
Attached Images
 
__________________
Dan
---------------------------------------------------------------------------------
If I recall correctly my memory is excellent, but my ability to access it is intermittent.
ss3964spd is offline   Reply With Quote
Reply

Stonetooling.com   Tile-Assn.com   National Gypsum Permabase


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tiling around and above Windows: how? Matthias Tile Forum/Advice Board 36 02-19-2020 04:10 PM
windows recovery Davestone Computer Training 8 05-21-2011 09:27 PM
How to keep your Windows PC clean DIYOHMY Computer Training 33 02-15-2005 11:23 PM
Windows??? wrf Tile Forum/Advice Board 17 10-26-2004 07:38 PM


All times are GMT -6. The time now is 01:43 AM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC