Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Tile & Stone Forums > Tile Forum/Advice Board

Sponsors


Reply
Thread Tools Search this Thread
Unread 10-06-2020, 07:06 PM   #16
Davy
Moderator -- Mud Man
 
Davy's Avatar
 
Join Date: Jan 2003
Location: Princeton,Tx.- Dallas area
Posts: 32,880
Remember post 6? "spend your time getting the floor flat first, it'll make it much easier to install the tiles."

Hind sight is 20/20 but if you would have skim coated the Ditra, filling the waffles, you could have popped lines in a grid like Paul mentioned.
__________________
Davy

www.davystephenstile.com
Davy is offline   Reply With Quote
Unread 10-19-2020, 04:19 AM   #17
CRB
Tile, stone and mosaic installer
 
CRB's Avatar
 
Join Date: Jan 2006
Location: Christchurch NZ
Posts: 253
Prepare the floor as well as possible - a little late now here, I acknowledge - the smaller the tile the less tolerance there is in relation to adjustment of the plane

Light - simply should not be used in this way!
Tiling should be carried out with lighting in finished room state as far as possible.
Edges throw shadows on anything. Tiles have edges!

Tiles like these are very different to large porcelain tiles of 2'x2' upwards and / or rectified edge tiles. The wedge / lash systems were dreamed up (I remember it was launched here in a thread - think I'm right? Tuscan? ) to accommodate issues thrown up by the advent of those types. These nice hex's are happily coming back into wider use.

Hope it goes well
__________________
CB

Colin Barber Tiling Co.
In Christchurch New Zealand. From London UK


www.colin-barber.com
CRB is offline   Reply With Quote
Unread 10-20-2020, 09:19 AM   #18
idred
Registered User
 
Join Date: Jul 2018
Posts: 39
The floor actually became decent considering the difficulty of installing these small hexagon tiles.

The hexagon tiles seem to come in two different shades of blue, one is slightly lighter/darker than the other. Hopefully you can see it in the picture.

When matching a grout color for these tiles, would you match the grout from the darker tile or the lighter tile?

Thanks

__________________
Edward
idred is offline   Reply With Quote
Unread 10-20-2020, 09:53 AM   #19
cx
Moderator emeritus
 
cx's Avatar
 
Join Date: Jul 2001
Location: Boerne, Texas
Posts: 91,224
That would be a purely aesthetic choice and best made by Mrs. Edward.
__________________
CX

Y'ALL NEW VISITORS READ THIS HERE!
cx is online now   Reply With Quote
Unread 10-20-2020, 04:48 PM   #20
idred
Registered User
 
Join Date: Jul 2018
Posts: 39
Yeah, It's hard to make up my mind. I'll probably lean towards the darker tile.

Would you know why these tiles are different colors? They came like that in the boxes, each box had mixed colors.

I emailed the place I bought them from and the store said they didn't know anything or know they were different colors.

Is this a manufacturing defect or were they two different colors for the looks?
__________________
Edward
idred is offline   Reply With Quote
Unread 10-20-2020, 09:57 PM   #21
cx
Moderator emeritus
 
cx's Avatar
 
Join Date: Jul 2001
Location: Boerne, Texas
Posts: 91,224
If your tiles meet the requirements of ANSI A137.1 they will have an Aesthetic Classification that will be indicated in the data sheet for the product. That looks like about a V2 class to my eye. If the tiles don't meet A137.1 I got no idea why they are different colors. Could be intentional, could be an error of some kind.

My opinion; worth price charged.
__________________
CX

Y'ALL NEW VISITORS READ THIS HERE!
cx is online now   Reply With Quote
Unread 10-28-2020, 06:35 PM   #22
idred
Registered User
 
Join Date: Jul 2018
Posts: 39
Hey guys, I was hoping someone could help me out once again.

I need to order color matched grout and because of the prices, I don't want to order too much.

I have exactly 54 square feet of these hexagon tiles. I tried to space them at 1/16", most are close but some are a little bit more.


Do you think 10 lbs of grout would definitely be enough? If not I would have to order 25lbs of color matched grout and it would be pretty expensive.

Thanks for any help.

Tiles are about 1/4" thick and 4" wide.


__________________
Edward
idred is offline   Reply With Quote
Unread 10-28-2020, 06:42 PM   #23
Kman
Moderator
 
Kman's Avatar
 
Join Date: Nov 2006
Location: NW Arkansas, Ozark Mountains
Posts: 11,628
I think it would be plenty for that.

Let me ask this: if you ran out with 10 pounds, would you have to wait a long time to get more?
__________________
Kevin

The top ten reasons to procrastinate:

1.
Kman is offline   Reply With Quote
Unread 10-28-2020, 07:59 PM   #24
idred
Registered User
 
Join Date: Jul 2018
Posts: 39
Thanks!

I don't think so, I think the issue may be more that the color matching may be off a little?

I'm ordering this from 360grout and its fairly expensive for this stuff compared to what you buy at home depot. The issue is, there are not many places to buy this color matched grout.

I think that color matched grout looks really good.
__________________
Edward
idred is offline   Reply With Quote
Unread 10-28-2020, 09:48 PM   #25
Kman
Moderator
 
Kman's Avatar
 
Join Date: Nov 2006
Location: NW Arkansas, Ozark Mountains
Posts: 11,628
They should have a coverage chart that would tell you based on the tile size, thickness, and the grout joint width. But with 1/16 - 1/8" joints I can't imagine you'd use more than ten pounds.

When I have a small amount and am concerned I might run out, I don't mix all of it. Maybe hold back 20%. Mainly the reason for that is if I accidentally add too much water, I can add a little more powder. But if you mix it all and add too much water, there's nowhere to go.
__________________
Kevin

The top ten reasons to procrastinate:

1.
Kman is offline   Reply With Quote
Unread 10-29-2020, 01:21 AM   #26
Tool Guy - Kg
Moderator -- Wisconsin Kitchen & Bath Remodeler
 
Tool Guy - Kg's Avatar
 
Join Date: Feb 2005
Location: Oak Creek, WI
Posts: 22,153
Is it really $88 for 10 pounds of grout?


__________________
Tonto Goldstein... but my friends call me Bubba

Help an awesome summer camp!
Tool Guy - Kg is offline   Reply With Quote
Unread 10-29-2020, 08:10 PM   #27
idred
Registered User
 
Join Date: Jul 2018
Posts: 39
Yes, but if you want the tile to be color matched you don't have many options. They took the time to color match my tile and I'm lucky they offer this service.

I really like the look of color matched grout with colored tile, it just adds so much to the look that its easily worth the cost, which is a very small cost when compared to the whole job.

Yes, its difficult to look at home depot prices for grout, but if you want a custom look, then you have to pay a little bit. It probably is also a difficult process to make this grout.

Money well spent for a nice unique look.

I'll let you guys know in this thread how everything turned out when I'm finally done.
__________________
Edward
idred is offline   Reply With Quote
Reply

Stonetooling.com   Tile-Assn.com   National Gypsum Permabase


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
LASH System of Radiant flooor heat fourml8r Tile Forum/Advice Board 18 01-21-2010 03:35 PM
LASH system question Aquera Professionals' Hangout 31 12-05-2009 05:11 PM
Qep's Lash system question. jbear666 Professionals' Hangout 19 06-20-2008 07:38 PM
Small hexagon bathroom tiles JCMullican Tile Forum/Advice Board 5 06-25-2001 10:16 PM


All times are GMT -6. The time now is 11:49 AM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC