|
Sponsors |
|
|
 |
|
12-12-2020, 06:51 PM
|
#91
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
I see now, ok i think my dremel will work. It took me forever to figure out that cut. I will try that CX. Then hope i can just chisel the thinset and replace.
__________________
Rigo
|
|
|
12-12-2020, 07:03 PM
|
#92
|
Moderator -- Wisconsin Kitchen & Bath Remodeler
Join Date: Feb 2005
Location: Oak Creek, WI
Posts: 22,519
|
How long has the chipped tile been set? Pulling tiles within a day are usually relatively easy. And they get much tougher with each passing day.
|
|
|
12-12-2020, 07:11 PM
|
#93
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
24 hrs
__________________
Rigo
|
|
|
12-12-2020, 07:15 PM
|
#94
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Its right at the entrance, if it were further back id leave it
__________________
Rigo
|
|
|
12-12-2020, 07:51 PM
|
#95
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
I went at it from the side with a large flat head and it came in two pieces pretty easy. Don't know if that's a good thing or not. Can I leave the clip feet in or should I remove and re install a new tile without them?
__________________
Rigo
|
|
|
12-13-2020, 08:13 AM
|
#96
|
Moderator
Join Date: Jul 2005
Location: Fairfax, Va
Posts: 3,934
|
Might want to remove the feet, Rigo. The feet are hard against the bottom of the existing tile. If you aren't careful with your mortar placement you might end up with mortar on top of the feet, thus possibly raising the height of the replacement tile.
__________________
Dan
---------------------------------------------------------------------------------
If I recall correctly my memory is excellent, but my ability to access it is intermittent.
|
|
|
12-13-2020, 10:16 AM
|
#97
|
Moderator -- Wisconsin Kitchen & Bath Remodeler
Join Date: Feb 2005
Location: Oak Creek, WI
Posts: 22,519
|
Quote:
Originally Posted by Rigo
I went at it from the side with a large flat head and it came in two pieces pretty easy. Don't know if that's a good thing or not.
|
Only being 24 hours, that’s normal. Today would have been harder and tomorrow would have been much harder, still.
|
|
|
12-13-2020, 01:10 PM
|
#98
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Thx y'all im back on track. Been trying to post this pic but keeps logging off when I hit submit. Any pro or DIYr in Tucson want this stuff, its free just come pick it up.
__________________
Rigo
|
|
|
12-19-2020, 01:02 PM
|
#99
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Floors are done I gotta drill holes in the tile for the washer drain pan and ready for baseboards. Any tips for that?
__________________
Rigo
|
|
|
12-19-2020, 01:24 PM
|
#100
|
Moderator
Join Date: Jul 2005
Location: Fairfax, Va
Posts: 3,934
|
What's that one big hole for, Rigo?
Your local BBS will have hole saws that will cut through the tile and mortar. You'll want to spritz it with water as you cut so the hole saw doesn't over heat. Not sure how they'll do cutting whatever is under though.
__________________
Dan
---------------------------------------------------------------------------------
If I recall correctly my memory is excellent, but my ability to access it is intermittent.
|
|
|
12-19-2020, 03:42 PM
|
#101
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Hi Dan, that's a drain for my washer pan. I bought a drill bit for tile and was gonna use that. Saw someone do it on u tube, wanted y'alls opinion.
__________________
Rigo
|
|
|
12-22-2020, 12:01 AM
|
#102
|
Moderator -- Wisconsin Kitchen & Bath Remodeler
Join Date: Feb 2005
Location: Oak Creek, WI
Posts: 22,519
|
I would highly advise against using that hammer-drill-bit for going through floor tile. You might get lucky...or you may do more damage than you think.
I’d recommend a diamond-grit holesaw. Unlike that carbide-tipped bit, a diamond-grit holesaw will grind its way through you tile. It’s quite gentle. Most box stores carry such bits for ~$10-$15.
|
|
|
12-22-2020, 08:41 PM
|
#103
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Ok Ill look into that KG. I think that's what Dan was trying to tell me too.
__________________
Rigo
|
|
|
12-31-2020, 10:35 PM
|
#104
|
Rigo
Join Date: Mar 2017
Location: Tucson, AZ
Posts: 77
|
Thx for the advice guy's my floors are done Happy New Year!!! I move to Texas in two weeks. My dads gonna have me do a tub to shower conversion when I get there, and im gonna need ALOT of help hehe. See ya soon, Rigo
__________________
Rigo
|
|
|
01-01-2021, 09:01 AM
|
#105
|
Moderator
Join Date: Jul 2005
Location: Fairfax, Va
Posts: 3,934
|
Glad you got it wrapped up, Rigo, nice way to end the year!
Good luck with your move. We'll be here when your dad puts you to work.
__________________
Dan
---------------------------------------------------------------------------------
If I recall correctly my memory is excellent, but my ability to access it is intermittent.
|
|
|
 |
|
 
 
Thread Tools |
Search this Thread |
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 02:56 PM.
|
|
|