Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Search Forums

Sponsors


Showing results 1 to 25 of 500
Search took 0.25 seconds.
Search: Posts Made By: Davy
Forum: Tile Forum/Advice Board Today, 08:04 PM
Replies: 2
Views: 62
Posted By Davy
It helps to have an extra piece to take with you....

It helps to have an extra piece to take with you. I'd check with your local stone supply showrooms. Looks like that stone varies in shade a lot anyway.
Forum: Tile Forum/Advice Board Today, 07:47 PM
Replies: 3
Views: 36
Posted By Davy
Hi CB, welcome. 1. Most of the time, I like...

Hi CB, welcome.
1. Most of the time, I like running the layout parallel with the longest wall. The front of the tub is usually not straight or square with the longest wall but it could be...
Forum: Tile Forum/Advice Board Today, 05:52 PM
Replies: 7
Views: 108
Posted By Davy
A wet saw is best. An angle grinder with a 4 inch...

A wet saw is best. An angle grinder with a 4 inch blade would do but with both tools, a lot depends on the blade you have.
Forum: Tile Forum/Advice Board Today, 05:47 PM
Replies: 7
Views: 108
Posted By Davy
You would want to draw straight lines on the...

You would want to draw straight lines on the plaster right where the edges of the tiles will be. That way you can slightly grind the paint off the plaster where the tiles will go. I wouldn't grind...
Forum: Tile Forum/Advice Board Today, 05:36 PM
Replies: 41
Views: 963
Posted By Davy
Jon, I'm not a Kerdi guy so I'm not sure what...

Jon, I'm not a Kerdi guy so I'm not sure what Schluter recommends but I would have stapled down tar paper and lath first.
Forum: Tile Forum/Advice Board Today, 05:29 PM
Replies: 4
Views: 67
Posted By Davy
Looks like a clamping drain to me. I see nails...

Looks like a clamping drain to me. I see nails sticking out of the OSB, makes me wonder if those are holding down the bottom flange section of the drain or if they go thru the copper pan.

Tommy,...
Forum: Tile Forum/Advice Board Today, 04:52 PM
Replies: 41
Views: 963
Posted By Davy
Mud won't stick to the top of the Kerdi. Thinset...

Mud won't stick to the top of the Kerdi. Thinset isn't designed for that but will work. Like Cx said, a mud bed could have been put down with the slope just right along with saving some money. Having...
Forum: Tile Forum/Advice Board Today, 04:38 PM
Replies: 11
Views: 225
Posted By Davy
You can also do your 1/3 stagger like this. Every...

You can also do your 1/3 stagger like this. Every 4th row lines up instead of every other row.
Forum: Professionals' Hangout Today, 04:25 PM
Replies: 105
Views: 8,747
Posted By Davy
I've heard of guys doing it this way for fence...

I've heard of guys doing it this way for fence posts. I still mix water into my concrete for fence posts even though it's not near as critical as a shower mud bed.
Forum: Tile Forum/Advice Board Yesterday, 04:15 PM
Replies: 11
Views: 225
Posted By Davy
Dan, if you haven't, lay out the tiles with...

Dan, if you haven't, lay out the tiles with wedges or spacers included to get a true layout. A picture of your back splash would help.
Forum: Professionals' Hangout Yesterday, 01:35 PM
Replies: 105
Views: 8,747
Posted By Davy
Richard, water is usually mixed into the cement...

Richard, water is usually mixed into the cement mix so all ingredients end up evenly distributed within the mud bed. Not only is there a risk of not adding enough water leaving powder at the bottom...
Forum: Tile Forum/Advice Board 06-03-2020, 06:29 PM
Replies: 7
Views: 108
Posted By Davy
Hi Karen. If the plaster is painted, it's best to...

Hi Karen. If the plaster is painted, it's best to grind it off so the tiles can be bonded right to the plaster coat.

Do you plan to cover the rounded corner with tiles too? If so, you might could...
Forum: Tile Forum/Advice Board 06-03-2020, 06:06 PM
Replies: 153
Views: 13,956
Posted By Davy
I probably don't use much more mud than you. John...

I probably don't use much more mud than you. John Bridge told me a long time ago that standing around time is very important. I'm pretty good at it these days. Always good to learn from the best.:D
Forum: Tile Forum/Advice Board 06-03-2020, 06:01 PM
Replies: 33
Views: 1,018
Posted By Davy
Nice job.:tup1:

Nice job.:tup1:
Forum: Tile Forum/Advice Board 06-02-2020, 10:04 PM
Replies: 41
Views: 963
Posted By Davy
Jon, most likely his Hydroban isn't sealed and...

Jon, most likely his Hydroban isn't sealed and bonded to the pan liner right at the floor. Moisture can wick up into the Hardi behind the Hydroban. Water will eventually get to the nails and rust...
Forum: Tile Forum/Advice Board 06-02-2020, 09:50 PM
Replies: 33
Views: 1,018
Posted By Davy
I'd only mix enough grout that can be used in...

I'd only mix enough grout that can be used in about 30 minutes, especially this time of year.
Forum: Tile Forum/Advice Board 06-01-2020, 04:21 PM
Replies: 5
Views: 154
Posted By Davy
I would also start full tiles at the wood floor...

I would also start full tiles at the wood floor as long as the cuts at the door are half size or bigger.
Forum: Tile Forum/Advice Board 05-31-2020, 06:25 PM
Replies: 4
Views: 217
Posted By Davy
Hi Dan. I don't know of anything myself. I don't...

Hi Dan. I don't know of anything myself. I don't think tile would hold up very well over asphalt. My dad use to say that tile is only as good as what's behind it. It's only a pretty surface.

Many...
Forum: Tile Forum/Advice Board 05-31-2020, 05:17 PM
Replies: 36
Views: 995
Posted By Davy
It sticks well to itself. :tup1:

It sticks well to itself. :tup1:
Forum: Tile Forum/Advice Board 05-31-2020, 05:13 PM
Replies: 41
Views: 963
Posted By Davy
I would ask him how he prepped the curb for tile....

I would ask him how he prepped the curb for tile. Ask him what he stuck the tiles to on the curb. If he says cement board, Denshield, Durock or anything other than mud, then he had to nail it, which...
Forum: Tile Forum/Advice Board 05-31-2020, 05:01 PM
Replies: 36
Views: 995
Posted By Davy
I'm not Cx but I've been called worse. :) Usually...

I'm not Cx but I've been called worse. :) Usually when I'm done, you can't see the Durock print thru it.
Forum: Tile Forum/Advice Board 05-31-2020, 04:33 PM
Replies: 36
Views: 995
Posted By Davy
Yes. This is called a ledger board and is...

Yes. This is called a ledger board and is especially handy when the perimeter isn't level. Set the board for the second row and come back and install the first row later.

That Redgard looks way...
Forum: Tile Forum/Advice Board 05-31-2020, 04:26 PM
Replies: 3
Views: 114
Posted By Davy
1. I would leave the joints open and silicone...

1. I would leave the joints open and silicone them after the thinset dries.
2. I'd use modified thinset.
3 &4. The thinset will set slow enough to get the stone set and adjusted as long as you...
Forum: Tile Forum/Advice Board 05-31-2020, 03:10 PM
Replies: 5
Views: 154
Posted By Davy
You'll likely get differing opinions and the only...

You'll likely get differing opinions and the only one that matters is yours. :) If this were mine, I'd run the tiles cross ways of the doors. That way the pattern can be seen when walking in and out.
Forum: Tile Forum/Advice Board 05-31-2020, 02:09 PM
Replies: 41
Views: 963
Posted By Davy
I'll add this, Jon. Looks like Cx and I were...

I'll add this, Jon. Looks like Cx and I were typing at the same time. His chicken pecking was faster than mine.:)

The job of the preslope under the liner is to give the liner slope towards the...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 11:29 PM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC