Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Search Forums

Sponsors


Showing results 1 to 25 of 500
Search took 0.10 seconds.
Search: Posts Made By: Kman
Forum: Tile Forum/Advice Board Yesterday, 08:08 PM
Replies: 6
Views: 159
Posted By Kman
I use a margin trowel to scrape as much as I can...

I use a margin trowel to scrape as much as I can out of the bucket at the end of the day. Then pour a little water in, maybe just 3-4 inches, and scrub the bucket clean with a stiff bristle brush so...
Forum: Tile Forum/Advice Board Yesterday, 07:34 PM
Replies: 1
Views: 66
Posted By Kman
I have an acrylic latex on my counter, and it's...

I have an acrylic latex on my counter, and it's worked fine for years. In the long run will it hold up like silicone? Definitely not, but if it lasts a few years I'll take it.

Either way you...
Forum: Tile Forum/Advice Board 10-21-2020, 09:53 PM
Replies: 14
Views: 343
Posted By Kman
If you've installed the tile over single-layer...

If you've installed the tile over single-layer plywood, you can expect to see this some more.

Plywood will also draw the moisture out of the mortar prematurely, and I think that's what caused...
Forum: Tile Forum/Advice Board 10-19-2020, 10:48 PM
Replies: 2
Views: 213
Posted By Kman
Welcome to the forum. :) I think your first...

Welcome to the forum. :)

I think your first step would be to find out for sure what you have on that wall to the left, other than the mortar you put up.

About the only method of waterproofing...
Forum: Tile Forum/Advice Board 10-19-2020, 09:59 PM
Replies: 2
Views: 253
Posted By Kman
Welcome to the forum, David. :) The drain...

Welcome to the forum, David. :)

The drain flange (the widest part of that drain) actually needs to be about an inch above the slab. That height will be the thickness of your mud pre-slope. Of...
Forum: Cleaning, Restoration and Sealing 10-19-2020, 03:20 PM
Replies: 6
Views: 341
Posted By Kman
Got any pictures of it?

Got any pictures of it?
Forum: Tile Forum/Advice Board 10-19-2020, 01:04 PM
Replies: 14
Views: 343
Posted By Kman
If we were to assume that the subfloor was...

If we were to assume that the subfloor was adequate as described by Jim, you'd still have to work lightning fast to to cover that mortar before it went off.

I've set a lot of tile, but I don't use...
Forum: Tile Forum/Advice Board 10-19-2020, 12:28 PM
Replies: 14
Views: 343
Posted By Kman
Did you tile directly to the plywood? And...

Did you tile directly to the plywood?

And you used a rapid setting mortar?
Forum: Tile Forum/Advice Board 10-18-2020, 10:51 PM
Replies: 2
Views: 190
Posted By Kman
I'd use a 1/4" square notch trowel for that size...

I'd use a 1/4" square notch trowel for that size tile.
Forum: Tile Forum/Advice Board 10-18-2020, 10:48 PM
Replies: 4
Views: 79
Posted By Kman
That's really up to the manufacturer, as to how...

That's really up to the manufacturer, as to how much of a tolerance they'll allow for flatness. It's one of the reasons I asked about the padding, as if it's thick enough, it might absorb the...
Forum: Tile Forum/Advice Board 10-18-2020, 09:10 PM
Replies: 4
Views: 79
Posted By Kman
I would want to cut away an of it that is loose. ...

I would want to cut away an of it that is loose.

But ideally you would remove all layers of flooring so you can see the condition of the subfloor. You certainly wouldn't want to put your new...
Forum: Tile Forum/Advice Board 10-18-2020, 08:10 PM
Replies: 14
Views: 343
Posted By Kman
What is the substrate?

What is the substrate?
Forum: Tile Forum/Advice Board 10-17-2020, 07:27 AM
Replies: 5
Views: 134
Posted By Kman
I would recommend you go with a 3/8" slope,...

I would recommend you go with a 3/8" slope, unless you plan to use pebbles on the floor, in which case you'll want to bump that up to 1/2".

If you're using a conventional liner and clamping drain,...
Forum: Tile Forum/Advice Board 10-15-2020, 09:24 AM
Replies: 7
Views: 179
Posted By Kman
I'd use white mortar for any natural stone. Gray...

I'd use white mortar for any natural stone. Gray can discolor it over time.

Also, while it's not necessary, you could cut a few grooves in the backside of that stone for the mortar to bite into. ...
Forum: Professionals' Hangout 10-13-2020, 09:15 PM
Replies: 12
Views: 475
Posted By Kman
I usually start out with a smaller but than what...

I usually start out with a smaller but than what I'll finish with. These bits (https://www.lowes.com/pd/Drill-America-Set-x-Set-Carbide-Tipped-Twist-Drill-Bit-Set/1001348398) are good to get a small...
Forum: Tile Forum/Advice Board 10-10-2020, 12:59 PM
Replies: 42
Views: 1,190
Posted By Kman
Here's the only thing about Diamond Board. Maybe...

Here's the only thing about Diamond Board. Maybe someone who's actually used it can verify this.

The TDS says it's "water resistant", not waterproof. And we know it has a gypsum core. In the...
Forum: Tile Forum/Advice Board 10-09-2020, 11:14 PM
Replies: 9
Views: 304
Posted By Kman
Are those 2x4's attached to the concrete wall by...

Are those 2x4's attached to the concrete wall by the 3 1/2" side, or the 1 1/2" side. If it's the former, that may explain the furring strips.
Forum: Tile Forum/Advice Board 10-09-2020, 05:03 PM
Replies: 42
Views: 1,190
Posted By Kman
Another thread about your backer board....

Another thread about your backer board. (https://www.johnbridge.com/vbulletin/showthread.php?t=125355)
Forum: Tile Forum/Advice Board 10-08-2020, 05:14 PM
Replies: 8
Views: 254
Posted By Kman
It's possible, if they were not bonded correctly,...

It's possible, if they were not bonded correctly, that they could come up in one piece. Of course, that would bring another more serious problem to light.

I would plan on them not being usable...
Forum: Tile Forum/Advice Board 10-07-2020, 01:32 PM
Replies: 2
Views: 141
Posted By Kman
Welcome to the forum, Alex. :) First, I...

Welcome to the forum, Alex. :)

First, I wouldn't add anything to the grout that wasn't recommended by the manufacturer. You don't know what results you'll end up with when you do an experiment...
Forum: Tile Forum/Advice Board 10-07-2020, 12:18 PM
Replies: 6
Views: 155
Posted By Kman
Asbestos is pretty good. :D I would go with...

Asbestos is pretty good. :D

I would go with one of the true cement boards like Durock, Permabase, or Wonderboard. The fiber cement boards like Hardibacker and Fiberock have some recycled paper...
Forum: Tile Forum/Advice Board 10-07-2020, 08:33 AM
Replies: 42
Views: 1,190
Posted By Kman
With their proprietary sealant, you do the nail...

With their proprietary sealant, you do the nail penetrations and seams, plus the joint between the bottom of the Densshield and the mud.
Forum: Tile Forum/Advice Board 10-06-2020, 01:31 PM
Replies: 42
Views: 1,190
Posted By Kman
Kerdi over Densshield is a big problem. You're...

Kerdi over Densshield is a big problem. You're putting mortar between two impervious surfaces, so it won't dry, at least for a very long time.
Forum: The Mud Box 10-06-2020, 01:24 PM
Replies: 8,672
Views: 1,482,343
Posted By Kman
I think it's very appropriate. When you look at...

I think it's very appropriate. When you look at it and vomit, you're already in the right room.
Forum: Tile Forum/Advice Board 10-06-2020, 05:31 AM
Replies: 61
Views: 1,852
Posted By Kman
Those wall boards cannot be run to the floor and...

Those wall boards cannot be run to the floor and held in place by the mud floor. The manufacturer does not allow them to be buried in the mud.

Quite frankly, they're not a good option for the...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 05:58 AM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC