Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Welcome to John Bridge / Tile Your World, the friendliest DIY Forum on the Internet


Advertiser Directory
JohnBridge.com Home
Buy John Bridge's Books

Go Back   Ceramic Tile Advice Forums - John Bridge Ceramic Tile > Search Forums

Sponsors


Showing results 1 to 25 of 500
Search took 0.22 seconds.
Search: Posts Made By: jadnashua
Forum: Tile Forum/Advice Board Yesterday, 10:39 PM
Replies: 11
Views: 247
Posted By jadnashua
There are a couple of tools designed to chew out...

There are a couple of tools designed to chew out a fitting from a hub. One of them is called a RamBit https://www.amazon.com/Pasco-3244-2-ram-bit/dp/B00SSKN0OC

Note, the original hub was tapered,...
Forum: Tile Forum/Advice Board Yesterday, 04:19 PM
Replies: 1
Views: 98
Posted By jadnashua
It depends somewhat on whether the tile is glazed...

It depends somewhat on whether the tile is glazed or not. IF it's glazed, it's harder to hide. IF it's a through-body porcelain, you can use diamond pads to soften the edge, but it's time...
Forum: Tile Forum/Advice Board Yesterday, 12:55 PM
Replies: 8
Views: 194
Posted By jadnashua
FWIW, what sold me on Grohe was a stay in London...

FWIW, what sold me on Grohe was a stay in London at a hotel where they had them installed...thermostatically controlled, so the temperature stayed the same regardless. With the older building, and...
Forum: Tile Forum/Advice Board 09-15-2021, 05:45 PM
Replies: 8
Views: 194
Posted By jadnashua
Note that Schluter does make a tiled cover...

Note that Schluter does make a tiled cover drain...I suppose you could use something like teak there, or, if you're using wood-look tile, then, it'd be easy to just tile it like it was intended.
...
Forum: Tile Forum/Advice Board 09-15-2021, 11:04 AM
Replies: 5
Views: 181
Posted By jadnashua
Interesting fact...the lignin in wood acts sort...

Interesting fact...the lignin in wood acts sort of like a very viscous liquid...it will flow under stress over time. That's why bookshelves, if they aren't supported along the span, eventually bow...
Forum: Tile Forum/Advice Board 09-14-2021, 06:06 PM
Replies: 5
Views: 192
Posted By jadnashua
It is very common to install linoleum onto 1/4"...

It is very common to install linoleum onto 1/4" luan, or similar hardwood plywood...that stuff is not good to have in the layup of a floor that is going to be tiled.

The tile industry guidelines...
Forum: Tile Forum/Advice Board 09-13-2021, 11:28 PM
Replies: 11
Views: 247
Posted By jadnashua
If anyone actually takes a bath, I'd still...

If anyone actually takes a bath, I'd still consider ditching the tub and going with a 66" one...when I remodeled, would have died for a 72" one, but the most the room could support was a 66" one...
Forum: Tile Forum/Advice Board 09-13-2021, 03:06 PM
Replies: 10
Views: 408
Posted By jadnashua
Two things to know about Hardiebacker, classified...

Two things to know about Hardiebacker, classified as a fiber-cement board:
- the instructions say you MUST terminate the end of the Hardiebacker above the mudbed, not embed it IN the mudbed (like...
Forum: Tile Forum/Advice Board 09-13-2021, 03:00 PM
Replies: 3
Views: 105
Posted By jadnashua
You could put the Kerdi directly on the block...

You could put the Kerdi directly on the block wall if it's clean! Or, if it's not clean or straight, you might consider making that wall out of KerdiBoard, which would give you a thermal break and a...
Forum: Tile Forum/Advice Board 09-12-2021, 05:15 PM
Replies: 15
Views: 558
Posted By jadnashua
IF there's a next time, you might consider tiling...

IF there's a next time, you might consider tiling to a thin sheet of Kerdiboard, and then once the thinset is cured, cut it like one huge tile. You could even do most of the grouting while it was...
Forum: Tile Forum/Advice Board 09-09-2021, 06:28 PM
Replies: 4
Views: 166
Posted By jadnashua
One of the issues would be the variations in...

One of the issues would be the variations in thermal expansion/contraction between the two materials...Due to thermal expansion CorianĀ® can expand up to 1mm per meter. A gap of at least 3mm should be...
Forum: Tile Forum/Advice Board 09-06-2021, 06:03 PM
Replies: 2
Views: 148
Posted By jadnashua
You'll pay a pretty premium if you can even find...

You'll pay a pretty premium if you can even find someone willing to set them at 1/32" gaps...plus, getting the joints filled with grout is a major pain. The grout helps to stabilize the assembly and...
Forum: Tile Forum/Advice Board 09-06-2021, 05:59 PM
Replies: 38
Views: 1,543
Posted By jadnashua
As long as you've offset the second layer so the...

As long as you've offset the second layer so the seams do not overlap and you don't have four corners meeting, it should work. Ideally, you'd have the sheets end at 1/3'rd the span between joists,...
Forum: Tile Forum/Advice Board 09-06-2021, 05:53 PM
Replies: 24
Views: 885
Posted By jadnashua
There are two big components to structural...

There are two big components to structural rigidity of a wooden floor system:
- along the joists
- in between the joists

It is quite rare for a house to be built to industry standards to install...
Forum: Tile Forum/Advice Board 09-04-2021, 08:32 PM
Replies: 24
Views: 885
Posted By jadnashua
FWIW, before I knew better, I used some mastic. ...

FWIW, before I knew better, I used some mastic. A little got onto some wood. Months later, I was able to wash that off...so much for permanence!

The material has its place, but it's generally...
Forum: Tile Forum/Advice Board 09-02-2021, 09:37 PM
Replies: 7
Views: 232
Posted By jadnashua
The square section in the pan slides up/down in...

The square section in the pan slides up/down in an adapter buried in the pan to account for the height of the tile. It's supported and partially locked in place with thinset, but once you can free...
Forum: Tile Forum/Advice Board 08-31-2021, 05:52 PM
Replies: 5
Views: 185
Posted By jadnashua
Schluter has at least one video on their US...

Schluter has at least one video on their US website showing putting up Kerdiboard onto concrete block walls with gobs of thinset on the wall surface...should be similar to the masonary except a block...
Forum: Tile Forum/Advice Board 08-30-2021, 12:06 PM
Replies: 3
Views: 162
Posted By jadnashua
Grout can have uneven color for a few reasons: ...

Grout can have uneven color for a few reasons:
- overwashing
- uneven depth
- improper mixing

A sealer does not literally 'seal' the grout, if it's even required. It SLOWS absorption of things...
Forum: Tile Forum/Advice Board 08-28-2021, 09:17 PM
Replies: 4
Views: 152
Posted By jadnashua
Again, not a problem...

Again, not a problem...
Forum: Tile Forum/Advice Board 08-28-2021, 07:10 PM
Replies: 8
Views: 218
Posted By jadnashua
As long as you've got more than 50% of the tile...

As long as you've got more than 50% of the tile bonded to the wall on that first row, it's not a big issue...the thinset might bond, but there, it's more of a support thing than actual bond.
Forum: Tile Forum/Advice Board 08-28-2021, 07:08 PM
Replies: 4
Views: 152
Posted By jadnashua
That shouldn't be an issue as long as you've...

That shouldn't be an issue as long as you've attached it properly to the studs. Almost all of the load is in shear, and the tile are stacked on top of each other on the walls, meaning the load is...
Forum: Tile Forum/Advice Board 08-28-2021, 07:05 PM
Replies: 24
Views: 885
Posted By jadnashua
Does anyone know of a cbu panel that allows...

Does anyone know of a cbu panel that allows installation with mastic underneath it? I've not seen one, but haven't perused the instructions carefully for awhile.

Your subflooring and cbu might...
Forum: Tile Forum/Advice Board 08-28-2021, 05:15 PM
Replies: 8
Views: 218
Posted By jadnashua
If I remember correctly, WEdi panels are just...

If I remember correctly, WEdi panels are just sealed with a bead of their sealant...tape not required, but then, it's been awhile since I read their instructions. I'd treat that joint like one...
Forum: Tile Forum/Advice Board 08-28-2021, 04:18 PM
Replies: 8
Views: 218
Posted By jadnashua
I'd put a bead of sealant on the flange, then set...

I'd put a bead of sealant on the flange, then set the Wediboard on top of it.
Forum: Tile Forum/Advice Board 08-27-2021, 09:34 PM
Replies: 24
Views: 885
Posted By jadnashua
Industry standards for a natural stone tile is...

Industry standards for a natural stone tile is TWO layers of subflooring, with the second one required to be plywood...then, whatever you want for a compatibility layer to set the tile, which CBU...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 07:33 AM.


Sponsors

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC