Ceramic Tile Advice Forums - John Bridge Ceramic Tile

Ceramic Tile Advice Forums - John Bridge Ceramic Tile (https://www.johnbridge.com/vbulletin/index.php)
-   Tile Forum/Advice Board (https://www.johnbridge.com/vbulletin/forumdisplay.php?f=1)
-   -   Ditra over Cement Backer board (https://www.johnbridge.com/vbulletin/showthread.php?t=113036)

Houston Remodeler 06-18-2014 09:31 PM

Those work well too. But you have to keep an eye out for screw jacking.

The screw shaft with no threads near the head is meant to allow the screw to spin and pull down the upper layer to the lower layer.

awdpsi 06-18-2014 09:33 PM

Thanks I assume screw jacking is where the screw lifts the top layer of ply up rather then fastenings it down?

Houston Remodeler 06-18-2014 09:34 PM

correct

awdpsi 06-21-2014 11:59 AM

Cut during layout?
 
I'm in the process of layout out all my tiles on the subfloor before I lay the ditra and mix thinset.

Do you think it's worth it to do all my cuts and literally have the entire floor cut and laid out before I put the ditra down and mix thinset?

Figured while it would take more time now it might make it faster for me when actually thin setting.

Also how large of a gap do I leave between the tile and wall, tub, saddle? 1/8 enough?

Thanks

cx 06-21-2014 12:09 PM

Scott, that's entirely a dealer's choice sorta decision. Some installers prefer to do all their cuts first based upon their layout lines, others do the entire layout of full tiles first and then do all their cuts, still others cut and set (or have their helper cut) and lay the entire floor in one pass. Do whatever seems to work best for you.

Perimeter movement accommodation joint should be at least 1/4" and usually doesn't show. At tubs and similar visible obstructions I'd recommend 1/8th" or one grout joint, whichever is larger.

My opinion; worth price charged.

awdpsi 06-21-2014 12:13 PM

Thanks cx. Also thanks for moving post. I was debating about which practice I should use here ( keep all questions together or separate them by relevance). I now know the answer.

Thanks again

awdpsi 06-22-2014 07:12 PM

So I ran into a ton of family issues this weekend and didn't get to laying tile.

I just finished putting down the ditra. My question is how long can I wait to tile?

With the ditra down now can I wait till Saturday, 5 days to tile ? Wasn't sure if there was a time that you must lay tile from the time ditra is set.

Houston Remodeler 06-22-2014 07:33 PM

You can wait as long as you'd like. Just refrain from rolling heavy objects over it.

Normal foot traffic is fine.

If in doubt, or you see you are crushing the ditra, add some pieces of plywood or drywall to the surface

awdpsi 06-22-2014 08:32 PM

Awesome! Thanks Paul!

CCDIYer 06-24-2014 07:20 PM

Hi Scott, I was curious as to how easy/hard it was and what method you used, to remove the excess thinset from your diagonal plank subfloor when you removed the cement board? You used a modified thinset correct?

I think you make the right call to correct your error and take up the CB, installing plywood in it's place.

awdpsi 06-24-2014 07:27 PM

Clare. A lot of the thinset seemed to come up attached to the cbu. There were plenty of areas where I used a wide pry bar to chip away at parts. Then I was using a heavy hammer to beat some of it into submission. Honesty it just took some time. Pulling up the cbu actually worked best using 3 pry bars like wide demo bars. I put them evenly spaced on one side of a sheet and would take turns smacking them in. It brought up the biggest sections.

awdpsi 06-26-2014 06:50 AM

Gentlemen, I come to you with a problem, AGAIN. In my hast to remove the CBU and install the plywood I missed a step.

I have a 2.5 ft x 2ft outcove where my toilet is that goes about 5/16 - 3/8" lower then the rest of the floor. Its a flat desent but 5/16-3/8" lower at the wall none the less. I had leveled this with the CBU in but then I ripped it up to add the 5/8" ply and forgot to address it.

Now the Ditra is down. (Im sick to my stomach again)....ANYHOW...is there any product that I could use over the Ditra to build up that 2ft x 2ft section up so the entire floor is flat? Any unmodified medium motars that I can use in that area to gain 5/16-3/8" so I can then put tile down.

Im sorry I am so dumb...I just figured this is still the best source for a valid solution. Im sure you will suggest ripping ditra up to level, but any suggestions are appreciated.


All times are GMT -6. The time now is 10:17 AM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2018 John Bridge & Associates, LLC